How To Remove Fireplace Door

Most doors attach at the top by means of a clamp assembly. If the doors seem crooked or loose, and if you are brave, you can try adjusting the clamps. As you might assume, thin glass doors are much more susceptible to breakage than thick ones. If it’s an eighth of an inch or thicker, you need to have your chimney swept by a professional. While this is a safety measure, it doesn’t replace a professional cleaning. While it can keep your chimney safer, it doesn’t do the same kind of job a professional cleaning will do. The truly ambitious might decide to clean their own chimneys. and if you try to spray any kind of cleaner on it, it will run right down. And you’ll want a good, clean sponge to make sure you’re getting rid of all of the residue. But if you have brick on your fireplace surround, then you’ll need to be a little more aggressive. In our project, we installed drywall over the entire wall to cover old paneling. Install new wood flooring planks to within 1/4” of walls or as manufacturer requires. Some of the doors are crooked and some stick or bind. A rustic wood beam mantel crowns the fireplace makeover and is ready to receive a display of beautiful accessories. Able to withstand high temperatures and resist breakage. Tracked bi-fold and cabinet style twin doors also available. Give your fireplace and its accessories routine cleaning throughout the wood-burning season to eliminate an accumulation of soot, ashes, and creosote tars. Inspect the firebox, flue, and chimney annually. Do not use water to drown a fire unless there is an emergency. When cleaning your fireplace, sprinkle damp coffee grounds over the cooled ashes to keep down the dust. Bifold glass doors are a traditional, functional and space-saving way to cover a fireplace. Repeat the procedure with the the other set of bifold doors. The reason you have to take them out is so that your new door frame will fit securely and properly. Make sure you get both the front of the screen and the back.

Approximate project time for a Hearth Technician is 15 minutes.Removing Fireplace Mesh Curtain and Replacing With New Steel Doors – How To Remove Masonry Fireplace Door

If you are noticing water in your fireplace, smoke not filtering through the chimney correctly, or any other oddity with your fireplace, do not continue to use it as it could be a fire hazard.

Creosote resin is what gets left behind in your chimney as you burn wood. Routine cleaning can keep the creosote from building up to dangerous levels. At the bottom, the doors are usually bolted into the inner hearth. Tempered glass can withstand very high temperatures if heated and cooled slowly. But obviously, if you hit the glass hard enough, it will break. Finally, if you have a two-sided fireplace (one with two openings), and you have glass doors, you must operate the fireplace with both doors open or with both doors closed.

It is hard to believe there was ever a fireplace here. Remove all brick that extends beyond the plane of the surrounding wall including the hearth. Apply the paste to a sponge, and use it to scrub off the black stains. All we need is the exact measurements of your firebox opening so that we outfit your fireplace in style with the perfect fitting, high-quality steel or extruded aluminum enclosure!

Whether you need bi-fold replacement doors or a cabinet style product, with mesh or without, we have a large assortment for you to choose from!

The inside fit requires more precise measuring and is used with custom enclosuresonly. I will be converting it to central air and heat. Is it on the first floor or second floor?

Some jobs could require the opening of walls. Most people relish their fireplace or they want to add a fireplace,” he said. Pocket doors are interior doors that slide into pockets of the wall. Pocket doors hang on wheels that suspend from a track on part of the frame inside the wall. It could be that the wheels need to be adjusted. Cracked wheels would also need to be replaced. You have to remove the molding then swing the door out. Burn only seasoned, well-dried wood. Never use an abrasive cleanser inside the fireplace. Mix one ounce of soap and one ounce of table salt with enough water to make a cream. The doors installed very easy (took me about a hour) and it absolutely tranformed the look of the fireplace. I have had other brands of fireplace doors over the years and through several homes, but these were the best. Hand-crafted to fit your fireplace exactly. Choose either a 3-sides frame with a draft assembly or a 4-sided frame with or without a draft assembly. Safety – protect children and pets from unstable screens, sparks, and flames. Our doors are 90% art, 10% function, & 100% delight! and if you could better use the space if it were a blank wall, or an extra bank of windows, or built-in storage, who’s to say a potential buyer wouldn’t also prefer that?

If you love the look of a proper mantel, and enjoy the ambience a fire brings to the room, consider converting your old wood-burning fireplace to gas.

Occasionally, the doors need to be removed to clean soot from the glass panes or to allow access to the fireplace. Some models may have a spring-loaded top pin instead of a separate spring clip that must be pushed down. Glass fireplace doors are actually only held in place by a few screws and adjustable clamps. It may be easier to find these brackets if you open the doors slightly and bend them out of the way. Once loosened, you can unscrew them the rest of the way with your fingers. It is not impossible but it is a royal pain. China will seal a door’s glass in a way that prevents it from being replaced. This will help the performance on any fireplace installed in tightly-constructed or well-insulated homes. Note that the first few fires you build in your wood burning fireplace should be small to help avoid excess cracking or spidering in the refractory.

I find the model or serial number? Using a non-approved door can block off cooling air into the firebox chassis and cause a potential fire hazard. I use the glass doors on my wood burning fireplace? Glass doors should be fully open when starting a fire and when the fire is burning strongly. If you have a see-through woodburning fireplace, the doors should be either closed or open on both sides when burning. The damper must be in the fully open position when using a wood burning fireplace. I have a fan kit on my wood burning fireplace but it doesn’t seem to blow much air. Stay tuned, because that’s exactly what we’re going to do in this episode. For this project, we’ll be dealing with three different surfaces, including wood, brick and metal. Next, we’ll remove the fireplace doors by removing the bracket assembly that clamps the unit to the firebox. However, we’re going to skip the roller and take our time using this brush, since we’d need it to paint all the grout lines anyway.

It’s a perfect example of how less can be more. That particular gold fireplace front looked out of place against the flagstone wall, and we’ve been thinking a lot about replacement options. After the clamps are loosened from within, the cover slides right off, like removing the picture frame from a beautiful painting. The fireplace, as it sat unused, really just needed a good cleaning. We also upgraded the shiny gold log holder we had on the hearth; that thing is though, what we “upgraded” to is actually much older, possibly the original set that was used with the house.

Little deer friend was sold as an umbrella holder, but we like it as everyday decor.

Tape around and over the firebox or fireplace insert and add drop cloths to protect the flooring. Fits masonry fireplace openings 30in. Always keep mesh panels closed and glass doors open when fire is burning in fireplace. The doors close with confidence and the magnets hold strong. I ran into was with the installation hardware. Unit is pretty heavy and has some height adjustability with a removable bottom section. I had the same unit at my old house and it held up well for 10 years. Make sure you measure and remeasure. But it works and it looks very nice. For the most part, assembly was pretty easy. The fiberglass insulation, however, was not nearly as neatly or easily separated as shown in the video. and there were scratches in the paint down to bare metal. My fireplace opening was larger then the max of 32 1/2″ tall but by putting two 1″ metal plates under doors all worked well.

It’s a bit draftier than my old doors when closed and not in use. With that door size, the frame will overlap the brick 3/4″ on each side and 1″ at the top with no stonework showing through the glass.

Can a fireplace door with tempered glass be closed when the fire is burning? Can you have a gas log fire going in a vented fireplace with the doors closed? If you are looking to burn with closed doors we suggest a door with ceramic glass. Do this when the doors are at room temperature and avoid harsh cleaning agents. They often emit a paint-like smell while the paint on the unit fully cures. This will create a lot of creosote which can lead to dangerous conditions in the chimney. This can also allow fumes and smoke into your house. A slammer is a fireplace insert that is put into the firebox and vented into the chimney without a properly sized vent pipe. For a wood stove, a failing gasket is another job easily done by many people. After cleaning out creosote and other debris, you might find yourself out of energy at the end of the job. Even if you brace it, you have only applied a temporary fix to the falling part of the problem. However, they do require maintenance which, if seen to regularly, won’t put much of a bite into your budget. I lock in to find something or someone to do a quality jobs, and it worth it. All custom fireplace doors are madeto your specifications and are non-returnable unless defective. All models styles in this section available. The smooth stone pops against the white walls and molding because of the stark difference in texture and color between the two elements.

Classic-lined built-ins integrate the fireplace, bookshelves, and an entertainment unit. Sandstone adorns the surround and blends beautifully with the built-in cabinets. If you love the look of a proper mantel, and enjoy the ambience a fire brings to the room, consider converting your old wood-burning fireplace to gas.

You have to get firewood and kindling, and store them properly, then build and tend to the blaze. If you rarely or never use yours, instead of looking at a roaring blaze like the one shown here, you are likely staring at a cold, black hole in the middle of your living room for most of the year.rnrn&l;b&g;3.

In a small space, storage trumps “extra” features every time — even considering resale value. Right up there with ample storage space is natural light … who doesn’t want more of that?

Traditional living rooms can be dark; imagine if you removed the fireplace and put in a new bank of gorgeous windows instead. I removed the doors from the packaging and began the installation only to find that with the configuration of my fireplace opening these won’t fit.

We purchased this door a week ago- and the first one arrived with a small weld mark in the frame- so we had to return it.

The color is a beautiful bronze- and goes well with our dark wood mantel. The product description says it will fit an opening height of between 22.5 ” to 32.5″. If the height of your fireplace is between 25.5″ to 32.5 it would be easy to install and look perfect. The installation wasn’t as easy as it could be, but was by no means difficult. The easiest method, which involves no drilling, only applies if your lintel bar (the. .. Also make sure your floor is level or the doors will sit slanted at the top. We raised one side up about 1/4″ on leftover matching hearth tile, extending out about 3/4″ out to fit under the 1″ deep unit.

From unpacking to finish it took about 2 or 3 hours of unhurried work to put everything together without anyone needed to help. The beveled glass of the bay window style doors give the unit a unique, expensive look. Read the entire add this one’s black the other is brass colored. This can be anything you want like a scrub brush, or abrasive sponge. The tool you use will depend upon preference and the surface you are cleaning. After you have chosen your tool, you can begin to apply it. Take your brush, sponge or cloth and apply the cleaner sort of like you are waxing a car. For more severe looking fireplaces, you will want to wait 30 or more minutes. For outdoor cleaning, simply take your hose or a bucket of water to rinse the area and flush off all of that soot, tar and dirt.

If you are indoors, the easiest, and least mess prone way to go is using a damp terry cloth towel. For regular cleaning, this will do the trick and make the surface look like new. If there are many layers of staining and soot built up on your fireplace, it is possible that it will take 2-3 applications to get it perfectly clean.

This particular stone has probably never been cleaned prior to this, and there was very little soot or smoke staining left on the rocks after going over it once.

Buy it for your fireplace and use it everywhere else when you are done. Brite is the best stain fighter, tub and tile cleaner, carpet shampoo and more. I want to use something safe that will work, but not damage my brick, because it would be very noticeable. I don’t want to ruin the looks of my fireplace. Even if the residue doesn’t catch on fire, it may heat to release dangerous gases once you burn wood. It won’t ruin the wall or effect the paint. It’s a light brick, the stains are severe and it looks very ugly. These are the two most important steps. It is the time you let it sit that most of the cleaning takes place, not the scrubbing you may or may not have to do afterward.

If the build-up is severe, it may take more than one application to produce a perfectly clean surface. Please let us know if you need any further help getting this to work for you. It is a gelatin type of paste that is more solid than liquid. If left in paste form, it should not cause you a problem. Make sure you let it sit long enough and it will break down that black layer and allow you to lift it off. Additionally, the damp coffee grounds is such a cost effective and downright neat way to create dust repellent. I envy your slick gray stonework — our fireplace has a similar insert, but ours is kind of dirty-brushed-brass. We have little kids — any concern with losing the “barrier” (whether perceived or real) that an insert provides?

I just don’t have the capacity to deal with all that. It only has a mesh screen, no glass, but we’ve had three winters worth of fires and so far haven’t had any kind of problem.

I couldn’t find another one with such clean lines with doors. I have no way of knowing what condition the brick is in behind it or if it will leave an obvious square mark once the cover is removed.

Fireplace doors keep warm air in your house. Open grates allow heat to escape up the chimney. Removing them will cause you heating bill to go up considerably. I did notice that it scratches right out. I can’t even latch our fireplace to close it. I applied one light coat but the next day it was rubbing off on my fingers like soot. I spent today removing the paint with mineral spirits. Does the high heat rustoleum paint really hold up?

I just happen to be the ring leader of our little o’l blog. If you have used firestarters and/or prefabricated logs, these products are bound together with a wax-type substance, which does not dissipate. Also check what is on top of the fireplace. This is quite a costly maintenance requirement. While our fireplace doors are drying, we’ll head back inside and paint the mantle. Even though we’re using the same shade of white, the difference in texture between the brick and the wooden mantle will provide just enough color contrast to add even more visual interest.

I make my fireplace more efficient? Before our fire place was sad and dirty looking even though it has probably had less then 20 fires burned in it over the last 30 years.

They kept sending me to their pile of pavers.