Leyland Truguard Hi Textured Exterior Paint

It can be applied and textured using the application/texture roller or it can be trowelled on and then textured with the same roller or with other rollers or tools.

Ensure good ventilation during application and drying. Hide default layout and size settings if they’ll be overridden anyway. Only show settings specific to mini-cart if configured to override global settings. The anti-carbonation properties resist the ingress of carbon dioxide from the atmosphere and reduces the deterioration of concrete and steel. Covers up to 8 square metres per litre per coat.

Ways of creating a uniform surface are all covered in-depth in the fourth video in the ‘This Is Sandtex Trade’ series. ‘This Is …CER 97 3401 Kalon Decorative Products. Leyland Truguard Hi textured – Leyland Truguard Hi Textured Masonry



I painted it all with sandtex fine textured paint but you can clearly see the different textures when the sun shines on it.

My question is would this work or is there a better paint to use and how textured is this paint? It is a very heavy material and there are a few ways of applying and texturing it. If you would like an even stipple then it can be sprayed using a hopper gun (my preference). Your cost could be £0.00 instead of £14.99. Also suitable for use on wallboards, concrete, cement rendering, brickwork and blockwork in internal situations. This paint has anti-carbonation properties that resist the onset of carbon dioxide from car exhaust fumes and prevent deterioration of concrete and steel. Fine textured waterbased masonry paint. Make sure handlers are only attached once if script is loaded multiple times. Trigger all logic that controls visibility of other settings. From decorators, builders merchants.


A range of ready-mixed colours are available. Provides excellent resistance to alkali. The anti-carbonation properties resist the ingress of carbon dioxide from car exhaust fumes and prevent deterioration of concrete and steel. White and a range of ready mixed colours. White and a selection of ready mixed colours. May be caused by surface contaminants or atmospheric attack. Seen as white furry crystalline deposits on new plaster and cement.

Leyland Trade Truguard Waterproofing Range

Glossy streaks or patchiness observed when viewing a surface from a shallow angle. Can be due to moisture at the time of, or slightly after, application eg dew, porous undercoat or grease under the surface.

Usually occurs with gloss finishes on exterior work where a rapid surface skin is formed. Ensure that the paint adheres effectively to the surface. Let each coat fully harden before further application. Keep paint to an even consistency and brush out to a thin, even coating. Normally dirty surfaces can be adequately cleaned with water and soap, or detergent. Previously painted surfaces should be rubbed down to provide a suitable key for subsequent coats of paint. This helps to avoid scratching the surface, and prevents the generation of dust. This also applies to any previously painted woodwork where bare wood areas are exposed, due to failed paint coatings. Ensure that wood is dry and free from oil, grease and any other contamination. Wash all remaining painted surfaces with water and detergent to remove any contamination. As discolouration or “bleeding” is likely to occur, normal paint systems cannot be used. All surfaces, new or old, should also be checked for any indications of organic growths, e.g. Rub down previously gloss painted surfaces with waterproof abrasive paper to provide a key for subsequent coats, rinse with clean water and allow to dry.

In addition a tendency to form powdery surface deposits of efflorescence can also cause subsequent failure. Flettons can be painted satisfactorily. Clean the surface to remove all traces of oil, grease and any other contamination. Iron and steel require very thorough surface preparation and protection with a suitable and effective paint system. It is imperative that there should be no delay before priming clean iron and steel as exposure to the air can cause surface deterioration in a very short time.

New bitumen or bituminous materials should not be painted except with further coats of bitumen, owing to the risk of bleeding or surface cracking.

Aluminium has a smooth even surface, containing a white oxide layer; it is therefore necessary to prepare the surface to provide a sufficient key.

Remove as much of the stain/smoke residue as possible with sugar soap, rinse well with clean water and allow to dry. Leyland products can be applied by spray. The method of spraying known as the airless system has now been in use in this country for many years and, therefore, should be familiar to most decorating firms and maintenance painters.

Leyland Paint Masonry